To support your selection of a suitable priming system for your application please find below a guidance.
Please note that this is only a guide. A recommendation always depends on the specific application.
Filling system for the automatic supply of glue machines with pourable granulate. The system can also be used for other pourable media.
Manual cover unit is a component of symelt ́s automatic filling system. It can be used for granulates at temperatures up to 80°C.
The cover unit is a component of symelt ́s automatic filling system. The cover unit ́s closing function avoids constant loss of heat from the tank of the connected hot-setting adhesive machine.
The Dispersion Surface Application System DSY-150 applies glue to paper webs with a fixed width of up to140mm. Other fixed widths are possible by exchange the width slot nozzle. Two different dispersion glues can be applied to a paper web, divided into inner and outer gluing. An inferior glue can be used for the inner surface and a higher quality glue for the edges.
The Dispersion Surface Application System DSY-V applies glue to paper webs with a variable width of up to 140mm. The width is adjusted by fully variable adjustment of the wide slot nozzle. Two different dispersion glues can be applied to a paper web, divided into inner and outer gluing. An inferior glue can be used for the inner surface and a higher quality glue for the edges.
Filling system BIG MASTER QX for the automatic supply of maximum 10 serially connected glue machines pourable granulate. The system can also be used for other pourable media.
The shunt is a component of symelt ́s automatic filling system, e.g., the SX, QX or VX type. Its special construction prevents thegranulate from sticking during transport and it minimizes the losses caused by movement.
Filling system for the automatic supply of 1 to maximum 6 glue machines with pourable granulate. The system can also be used for other pourable media.
Filling system BIG MASTER VX for the automatic supply of maximum 20 glue machines pourable granulate (Connection of further glue machines on request). The VX can be supplied with max. 4 pressure chambers and therefore four lines. At each pressure chamber max. 10 glue machines can be connected serially (total max. 20). The system can also be used for other pourable media.
Priming unit for evacuation of centrifugal pumps pumping clean or slightly contaminated fluids and where dry running is admissible for short periods of time.
Level controlled priming systems for evacuation of centrifugal pumps pumping clean or slightly contaminated fluids. Due to the level-control, the system is also suitable for plants where gas- or air inclusions have to be separated effectively even during operation of the centrifugal pump.
Automatic aspirator designed for centrifugal pumps where dry running is admissible for short periods of time.
Pressure controlled priming unit for evacuation of centrifugal pumps used in hazardous explosive area, e.g. on board ships. Re-evacuation after break of pump delivery during pump operation.
Automatic aspirator designed for the priming of centrifugal pumps where dry running is not admissible.
Pressure controlled priming unit for evacuation of centrifugal pumps used in hazardous explosive area, e.g. on board ships. Pump start signal when pre-evacuation is completed. Re- evacuation after break of pump delivery during pump operation.
Level controlled automatic priming unit for pre- and re-evacuation of individual or several centrifugal pumps.
Level controlled priming unit for effective pre- and re-evacuation of centrifugal pumps used in hazardous explosive area, e.g. on board ships. Pump start signal when pre-evacuation is completed. Effective re-evacuation due to separate installation in front of the centrifugal pump and level controlled evacuation independent from pump discharge pressure.
Level controlled automatic priming unit for pre- and re-evacuation of individual or several centrifugal pumps.
Level controlled priming unit for effective pre- and re-evacuation of centrifugal pumps used in hazardous explosive area, e.g. on board ships. Pump start signal when pre- evacuation is completed. Effective re-evacuation due to separate installation in front of the centrifugal pump and level controlled evacuation independent from pump discharge pressure.
Diesel driven vacuum pump for evacuation of centrifugal pumps and siphon pipes.
Vacuum pump to exhaust gas, air and steam. Pump free of flat clearance surfaces, extensive insensitive to solid components of the service liquid. By this the pump is specially suited for priming units of pumping plants equipped with centrifugal pumps. By means of the self-controlled outlet valve the pump is automatically adjusted to variable pressure conditions.
Evacuation of centrifugal pumps with diesel driven engine and electrical battery starters, suitable for clean or slightly contam- inated media.
Evacuation of centrifugal pumps with diesel driven engine, suitable for clean or slightly contaminated media.
Manually operated vacuum compressed air ejector, e.g. for evacuation of e.g. centrifugal pumps.
Level controlled priming system with independent service liquid supply for evacuation of centrifugal pumps pumping clean or slightly contaminated fluids. Due to the level-control, the system is also suitable for plants where gas- or air inclu- sions have to be separated effectively even during operation of the centrifugal pump.
Autoseparator for evacuation of centrifugal pumps pumping clean or slightly contaminated fluids. The system is specially used in case of heavily gassing media (e.g. gasoline), media having considerable air and gas inclusions, as well as for evacuation of suction lines with relative peak points.
Priming Unit for automatic start-up evacuation of centrifugal pumps pumping clean or slightly contaminated media.
Fully automatic level-controlled compact priming system for the evacuation of single or several centrifugal pumps, especially in pump stations for the pumping of heavily contaminated pump- ing media such as e.g. untreated sewages, sludge, sinter water a.s.o.. Also used for the evacuation of siphon pipes.
Fully automatic level-controlled compact priming system for the evacuation of single or several centrifugal pumps, especially in pump stations for the pumping of heavily contaminated pumping media such as e.g. untreated sewages, sludge, sinter water a.s.o.. Also used for the evacuation of siphon pipes.
Level controlled priming systems for evacuation of centrifugal pumps diesel engine motors and electric battery charging equipment, suitable for use in plants pumping sets or dredging pumps, sewage pumps emergency pumps, irrigation pumps, ...
Pressure controlled central vacuum unit for permanent evacuation of centrifugal pumps for the delivery of clean or slightly contaminated fluid. The pressure control enables the unit to be connected with pumps, working under different suction conditions.
Automatic aspirator designed for the priming of centrifugal pumps where dry running is not admissible.
Pressure controlled priming unit for evacuation of centrifugal pumps used in hazardous explosive area, e.g. on board ships. Pump start signal when pre-evacuation is completed. Improved re-evacuation after break of pump delivery during pump operation due to separate installation in front of the centrifugal pump.
Automatic aspirator for evacuation of centrifugal pumps pumping clean or slightly contaminated fluids. Special design for service in explosive area.
Automatic aspirator designed for centrifugal pumps where dry running is admissible for short periods of time.
Autoseparator for evacuation of centrifugal pumps pumping clean or slightly contaminated fluids. The system is specially used in case of heavily gasing media, media having considerable air and gas inclusions, as well as for evacuation of suction lines with relative peak points.
Automatic aspirator for evacuation of centrifugal pumps. Special design for chemical aggressive pumping media.
Fully automatic central vacuum unit, pressure controlled, designed for permanent evacuation of several centrifugal pumps handling clean to slightly contaminated liquids. The pressure control enables systems with different suction levels to be connected.
Fully automatic central vacuum unit designed for level- controlled, permanent evacuation of several centrifugal pump units handling clean to lightly contaminated liquids. It is essen- tial that the centrifugal pumps have to operate on the same suction level.
Drainage of small spaces, tank fields, etc.
For the draining of free-flowing surface scum from the surface of basins, suction chambers of pumps etc.
Gully-Drainer for automatically-controlled collecting of dangerous fluids from the street surface and to close the sewerage system in case of disaster with tank trucks etc.
Drainer system for ground water sanitation; fully automatic skimming of floating pollutants (oil, etc) practically free from phase shift, out of ground water.
2-step de- and aeration valve for sewage water pump discharge pipes. Due to a free suspended floater and dispense with lever, joints and pivot the valve is insensitive against solid and sedimentation.
Automatic discharge of air or gas from centrifugal pumps and suction systems to a central vacuum unit, e.g. vatec-Type TDV, TDES or AELZ.
Automatic discharge of air or gas from centrifugal pumps and suction systems to a central vacuum unit, e.g. vatec-Type TDV or AELZ.
Automatic discharge of air or gas from centrifugal pumps and suction systems to a central vacuum unit, e.g. vatec-Type TDV, TDES or AELZ.
Level-controlled gas discharge valve for automatic discharge of air or gas from siphon pipes via a pressure-controlled central vacuum unit, e.g. vatec-central vacuum unit type TDV.
Separator for evacuation of centrifugal pumps pumping clean or slightly contaminated fluids. The system is specially used in case of heavily gassing media (e.g. gasoline), media having considerable air and gas inclusions, as well as for evacuation of suction lines with relative peak points.
Automatic shut-off valve for pipelines to prevent gas flow.
Inlet nozzle for pump suction pipes.
Vertical mounted and membrane operated breaker valve to prevent back flow in discharge side siphon pipes.
Throttle valve for installation at the discharge side of centrifu- gal pumps serves for reducing the unloading process and to ensure higher purification in pump systems with priming sys- tems. The throttling aids evacuation processes by hindering the formation of air vortices at suction inlets.
Non-Return Valve for clean to lightly contaminated liquids. Flow in arrow direction.
Protective strainer fur succeeding piping and pumps.
Float controlled level indicators, e.g. for use as starting signal for centrifugal pumps when evacuation is finished.
Pressure monitoring of liquid supply systems, etc. Dry-run protection and automatic shut-off device for centrifugal pumps For clean or slightly contaminated liquids. Nozzle connection.
A jerrycan filling station for the cleaning and filling of 21 20-liter palletized fuel jerrycans simultaneously.
Fully automatic central vacuum unit designed for level-controlled, permanent evacuation of several centrifugal pump units handling clean to lightly contaminated seawater. It is essential that the centrifugal pumps have to be evacuated operate on the same suction level.
Mobile suction system integrated in an assembly case for evacuating sprinkler systems.
Level controlled priming systems for evacuation of centrifugal pumps pumping clean or slightly contaminated fluids. Due to the level-control, the system is also suitable for plants where gas- or air inclusions have to be separated effectively even during operation of the centrifugal pump.
Fully automatic central vacuum unit, pressure controlled designed for permanent evacuation of several centrifugal pumps or siphon pipes handling clean to slightly contaminated liquids. The pressure control enables systems with different suction levels to be connected. Each suction point is linked to the vacuum collection line via gas discharge valves.
Fully automatic level-controlled compact priming system for the evacuation of single or several centrifugal pumps, especially in pump stations for the pumping of heavily contaminated pumping media such as e.g. untreated sewages, sludge, sinter water a.s.o.. Also used for the evacuation of siphon pipes.
Fully automatic central vacuum unit designed for level-controlled, permanent evacuation of several centrifugal pump units handling clean to lightly contaminated liquids. It is essential that the centrifugal pumps have to be evacuated operate on the same suction level.
Automatic vacuum system for central evacuation of several siphon pipes and/or centrifugal pumps.
SITEMAP
vatec-Maschinenbau GmbH
Hans-Bredow-Strasse 49
28307 Bremen